MDS MDS iNET 900 Specifikace

Installation & Start-Up Wireless IP/Ethernet Transceiver iNET-II Firmware Release 1iNET Firmware Release 6 MDS 05-2873A01, Rev. EMAY 2006 Microwa

8 i NET Series Installation & Start-Up MDS 05-2873A01, Rev. E Step 2—Install the Antenna To minimize radio frequency interference, the antenna

MDS 05-2873A01, Rev. E i NET Series Installation & Start-Up 9 • Device Mode —Access Point, or Remote (default).• Network Name — Common identifier

10 iNET Series Installation & Start-Up MDS 05-2873A01, Rev. E c. Press the ENTER key. A login screen will be displayed that requires a password

MDS 05-2873A01, Rev. E iNET Series Installation & Start-Up 11Step 6—Check for Normal OperationIn this step you will verify the proper operation of

12 iNET Series Installation & Start-Up MDS 05-2873A01, Rev. E c. When the network is operating properly based on observation of the unit’s LEDs,

MDS 05-2873A01, Rev. E iNET Series Installation & Start-Up 13These include identifying interference and taking corrective steps such as skipping s

14 iNET Series Installation & Start-Up MDS 05-2873A01, Rev. E AIMING DIRECTIONAL ANTENNASIn general, signal levels stronger than –80 dBm will pro

MDS 05-2873A01, Rev. E iNET Series Installation & Start-Up 15TRANSMITTER POWER AND ANTENNA SWR TESTThe following procedure may be used to measure

16 iNET Series Installation & Start-Up MDS 05-2873A01, Rev. E TROUBLESHOOTINGIt is best to begin troubleshooting at the Access Point, because the

MDS 05-2873A01, Rev. E iNET Series Installation & Start-Up 17LINK LED does not light. a. Network Name of Remote not identical to desired Access Po

Refer to the Installation Reference Chart at the middle of this manual for essentialinstallation and configuration details.

18 iNET Series Installation & Start-Up MDS 05-2873A01, Rev. E Cannot access the MS through COM1a. Connect to unit via Telnet or Web browserb. Dis

MDS 05-2873A01, Rev. E iNET Series Installation & Start-Up 19SPECIFICATIONSGENERALTemperature Range: –30° C to +60° C (–22° F to 140° F)Humidity:

20 iNET Series Installation & Start-Up MDS 05-2873A01, Rev. E TECHNICAL ASSISTANCETechnical assistance for MDS products is available from our Tec

Installation Guide

Microwave Data Systems Inc.Rochester, NY 14620General Business: +1 585 242-9600FAX: +1 585 242-9620Web: www.microwavedata.com175 Science ParkwayA prod

MDS 05-2873A01, Rev. E i NET Series Installation & Start-Up 1 Contents OPERATIONAL & SAFETY NOTICES ...2PROD

2 i NET Series Installation & Start-Up MDS 05-2873A01, Rev. E Manual Revision and Accuracy While every reasonable effort has been made to ensur

MDS 05-2873A01, Rev. E i NET Series Installation & Start-Up 3 When installed in a Class I, Div. 2, Groups A, B, C or D hazardous location, observ

4 i NET Series Installation & Start-Up MDS 05-2873A01, Rev. E PRODUCT DESCRIPTION The MDS iNET-II and iNET transceivers are designed to provide

MDS 05-2873A01, Rev. E i NET Series Installation & Start-Up 5 Differences Between iNET and iNET-II The iNET and iNET-II Transceivers, while simil

6 i NET Series Installation & Start-Up MDS 05-2873A01, Rev. E INSTALLATION PLANNING This section provides tips for installation and start-up of

MDS 05-2873A01, Rev. E i NET Series Installation & Start-Up 7 It is highly recommended that the Access Point unit be installed first. With this