MDS MX-2104 Specifikace Strana 205
- Strana / 243
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MX-2100/2104 Installation and Operation Manual Appendix F Command Set Description
Commands F-27
The password entry screen appears, e.g.,
NEW PASSWORD (4 to 8 CHARS) =
CURRENT PASSWORD = 'password'
2. Type the required password (spaces are recognized as valid characters in a
password).
The password appears on the second line.
3. Carefully check that the specified password has been indeed typed in, and
then press ENTER.
The new password takes effect, and the MX-2100 prompt reappears.
DEF ROUTE
Purpose
Enables static routing of management information to network devices that do not
support the proprietary RIP routing protocol used by the MX-2100. The IP
addresses of such devices should be defined here.
By using this command you can declare an IP address on the list as an Ethernet
address. When an agent searches for this IP address, it will be directed to the
Ethernet.
Format
DEF ROUTE
Use
• Type:
Def route <ENTER>
The MX-2100 displays the following data form:
KM2100>def route
CURRENT ROUTE PARAMETERS
-------------------------
ROUTE IP ADDRESS 1 IS :000.000.000.000
ROUTE IP ADDRESS 2 IS :000.000.000.000
ROUTE IP ADDRESS 3 IS :000.000.000.000
ROUTE IP ADDRESS 4 IS :000.000.000.000
ROUTE IP ADDRESS 5 IS :000.000.000.000
ROUTE IP ADDRESS 6 IS :000.000.000.000
ROUTE IP ADDRESS 7 IS :000.000.000.000
ROUTE IP ADDRESS 8 IS :000.000.000.000
ROUTE IP ADDRESS 9 IS :000.000.000.000
ROUTE IP ADDRESS 10 IS :000.000.000.000
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
- MX-2100/2104 1
- MICROWAVE DATA SYSTEMS, INC 3
- FCC-15 User Information 4
- Preface 5
- Conventions 6
- Related Documentation 6
- Quick Start Guide 7
- Contents 9
- Chapter 4 Operation 10
- Chapter 5 Diagnostics 10
- Table of Contents 11
- Table of Contents 12
- List of Figures 13
- List of Tables 14
- Chapter 1 17
- General Information 17
- 1-2 Functional Description 18
- Local MX-2100 Management 20
- Remote MX-2100 Management 20
- Supervision Terminal 21
- 1.2 Physical Description 22
- MX-2100 Rear Panel 23
- MX-2100 Front Panel 24
- MX-2104 Rear Panel 25
- MX-2104 Front Panel 26
- Common Logic Modules 26
- Main Link Modules 26
- Power Supply Modules 27
- I/O Modules 28
- Physical Description 1-13 29
- 1-14 Physical Description 30
- Physical Description 1-15 31
- Basic MX-2100 System 32
- Redundancy (not for MX-2104) 36
- Bypassing Configurations 39
- Location A Location C 41
- Location B 41
- Switch Mode 46
- System Management 48
- In-Band 50
- Out-of-Band 51
- KCL KCL KCL 52
- KCLKCL KCL 52
- System Timing Considerations 54
- A. Leased Line Confi 55
- B. Digital Configuration 55
- Data Channel Clock Modes 61
- Sub Link Timing 63
- 1.4 I/O Module Applications 66
- Chapter 2 71
- Installation 71
- Input Power Requirements 72
- Grounding 72
- Ambient Requirements 73
- 2.3 Equipment Needed 78
- Equipment Needed 2-9 79
- 2-10 Equipment Needed 80
- 2.4 Package Contents 81
- MX-2100 82
- MX-2104 82
- KPS Module 83
- KCL.2 Module 84
- Installing the KCL.2 Module 85
- Table 2-5 90
- Internal MX-2100 Settings 91
- Connections 91
- Initial Configuration 91
- Chapter 3 93
- Configuring MX-2100 93
- Front Panel Menu 94
- Chapter 4, Operation 95
- See Figure 3-2B 96
- See Figure 3-3C 96
- See Module 96
- Manuals in Part II 96
- Only for Data 97
- Channels 97
- Chapter 4 105
- Operation 105
- Command Options 106
- Command Protocol 107
- Index of Commands 108
- See Insert 111
- RTSM-LEAD 112
- E-LEAD DCD 112
- DATAVOICE 112
- 4.4 Operating Instructions 116
- PASSWORD> 118
- KM2100> 118
- KM2104> 118
- TERMINAL ON LINE 118
- Control Session 119
- Ending a Control Session 119
- Front Panel 120
- Normal Indications 121
- Turn Off 122
- Chapter 5 123
- Diagnostics 123
- Special Considerations 124
- Diagnostic Tests 5-3 125
- 5-4 Diagnostic Tests 126
- Diagnostic Tests 5-5 127
- 5-6 Diagnostic Tests 128
- Diagnostic Tests 5-7 129
- Main Link Loops 130
- User or Test 131
- Equipment 131
- 5-10 Diagnostic Tests 132
- I/O Module Loops and Tests 134
- CHANNEL 1 135
- PRBS Transmission 136
- BERT Testing 136
- 5-16 Diagnostic Tests 138
- Appendix A 139
- Connection Data 139
- A.3 MNG Connector 141
- A.4 Alarm Relay Connector 142
- Appendix B 143
- B-2 Alarm Messages 144
- Alarm Messages B-3 145
- B-4 Alarm Messages 146
- Alarm Messages B-5 147
- B-6 Alarm Messages 148
- Alarm Messages B-7 149
- B-8 Alarm Messages 150
- Alarm Messages B-9 151
- Appendix C 159
- SNMP Management 159
- MIB Structure 160
- SNMP Communities 161
- C.3 IP Environment 162
- IP Environment 163
- Automatic IP Traffic Routing 164
- Network B 165
- Network A 165
- Network C 165
- C.4 SNMP Traps 166
- Appendix D 167
- Software Download 167
- Windows-Based Stations 169
- Appendix E 171
- Configuration Parameters 171
- E-2 General 172
- General E-3 173
- E-4 General 174
- General E-5 175
- E-6 General 176
- General E-7 177
- E-8 General 178
- Appendix F 179
- Command Set Description 179
- F.2 Commands 180
- CLR LOOP 181
- CLR MONITOR 182
- CONNECT SWITCH 182
- Purpose 183
- DEF AGENDA 184
- DEF AGENT 185
- F-8 Commands 186
- DEF ALM DEBOUNCE 187
- DEF CALL 187
- DEF CON 190
- Commands F-13 191
- DEF DB FLIP 192
- DEF FRAME 195
- DEF MANAGER LIST 196
- DEF ML CALL 198
- Commands F-21 199
- F-22 Commands 200
- Commands F-23 201
- DEF NAME 202
- DEF NODE 202
- DEF PWD 204
- DEF ROUTE 205
- DEF SYS 207
- Table F-5. System Parameters 208
- DISCONNECT SWITCH 210
- DSP AGENT 211
- DSP ALM 212
- DSP BERT 212
- DSP CH CON 213
- DSP FLIP 214
- DSP HDR TST 215
- DSP MANAGER LIST 215
- DSP KVF5 216
- DSP PBX 216
- DSP KVF6 217
- DSP SIGNALING 218
- DSP SIG 218
- DSP PRBS_INJ 218
- DSP REM AGENT 219
- DSP REV 219
- DSP ST FRAME 220
- Commands F-43 221
- DSP ST ML 222
- Commands F-45 223
- DSP ST SLOT 224
- Commands F-47 225
- DSP ST SYS 226
- Commands F-49 227
- EDIT DB 228
- FLIP ML 229
- INIT DB 230
- LOAD DB 1\2 232
- LOAD IO 232
- ML RECOVERY 234
- MONITOR 234
- REBUILD FRAME 234
- RESET LOC 235
- RESET IO 235
- RESET ML 235
- UPDATE DB 1\2 236
- Downloading Procedure, D-3 241
- Figure 1 243
Související produkty a manuály pro Sítě MDS MX-2104
Sítě MDS Orbit MCR-4G Průvodce nastavením
(4 stránky)
(4 stránky)
Sítě MDS MX-2100 Uživatelský manuál
(70 stránky)
(70 stránky)
Sítě MDS Orbit MCR-4G Specifikace
(146 stránky)
(146 stránky)
Sítě MDS Orbit MCR-4G Uživatelský manuál
(4 stránky)
(4 stránky)
Sítě MDS TransNET 900 Uživatelský manuál
(14 stránky)
(14 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce